EFFECT OF MULTI-INTERVAL HEATING ON THE FORMING QUALITYOF ADVANCED PULTRUSION PARTS

Abstract

Abstract: Advanced pultrusion molding technology takes prepreg as raw material, realizes the mechanical property designability of the parts through the combination of different layers, and has unique advantages in controlling the production cost and flexibility. This subject selects X850 prepreg for research, analyzes the difference between its typical hot pressing tank forming process and advanced pultrusion process. The function of each interval in the forming process is analyzed for the characteristics of hot-pressure curing in advanced pultrusion molding. The curing kinetics of resin in X850 prepreg is measured through differential scanning calorimetry. The selection principle of temperature system in each interval is determined. In order to prevent the formation and growth of pores, the pressure system of each interval is reasonably selected. A curing process experimental scheme is designed by means of orthogonal experiment, and the influence trend of multi-interval temperature system and pressure system on the forming quality of parts is studied. The specimen is prepared by the equipment designed by the laboratory, and the scheme No. 6(with pretreatment temperature at 160 ℃ for 30 min, curing temperature at 180 ℃ for 20 min and curing pressure at 0.8 MPa)is selected as the final pultrusion process in the orthogonal test scheme, for which the bending strength, interlaminar shear strength and porosity are characterized.

Key words: advanced pultrusion, prepreg, DSC, curing degree, void content

CLC Number:

TB332

WANG Yu, QI Jun-wei, WANG Yue-quan, XIAO Jun. EFFECT OF MULTI-INTERVAL HEATING ON THE FORMING QUALITYOF ADVANCED PULTRUSION PARTS[J]. Fiber Reinforced Plastics/Composites, 2019, 0(10): 10-18.

References

[1]中国航空研究院. 复合材料结构设计手册. 北京: 航空工业出版社, 2001: 340-375.
[2] 丁传荣. 拉挤-缠绕设备与工艺技术研究. 纤维复合材料, 1998(4): 21-24.
[3] Brosius D, Writer C. Advanced pultrusion takes off in commercial aircraft structures. European Journal of Cell Biology, 1997, 71(4): 414-422.
[4] Leipold M, Garner C E, Freeland R, et al. ODISSEE-A proposal for demonstration of a solar sail in earth orbit. Acta Astronautica, 1998, 45(4-9): 557-566.
[5] Dale B. Advanced pultrusion takes off in commercial aircraft structures. High-performance Composites, 2003(9): 36-39.
[6] Toru K, Makoto O, Shuntaro K. Method and apparatus for continuous molding of fiber reinforced plastic member with curvature: US 20050029707. 2005-02-10.
[7] 乌云其其格, 廖子龙. 中温固化树脂/碳布复合材料工艺性能研究. 航空材料学报, 2006, 26(5): 65-69.
[8] 乌云其其格, 廖子龙, 李明. 3233树脂及其复合材料性能研究. 玻璃钢/复合材料, 2003(6): 16-18.
[9] 谢旻, 顾轶卓, 李敏, 等. 碳纤维/双马树脂预浸料固化过程动态力学性能. 复合材料学报, 2010, 27(4): 52-58.
[10] Becker O, Cheng Y B, Varley R J, et al. Layered silicate nanocomposites based on various high-functionality epoxy resins: The influence of cure temperature on morphology, mechanical properties,and free volumn. Macromolecules, 2003, 36(5): 1616-1625.
[11] Huang Y, Young R J. Interfacial behaviour in high temperature cured carbon fibre/epoxy resin model composite. Composites, 1995, 26(8): 541-550.
[12] Kuriyama S. Method for continuously forming composite material into a rigid structural member. Composites Manufacturing, 1994, 5(4): 243-245.
[13] 李云雁, 胡传荣. 实验设计与数据处理. 北京: 化学工业出版社, 2008.
[14] 赵选民. 试验设计方法. 北京: 科学出版社, 2006.

[1]	MA Shiheng, GE Jingran, LIU Kai, LI Yongshan, LIANG Jun. Study on specific heat capacity and thermal conductivity of glass fiber/epoxy resin prepreg during the whole curing process [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(4): 20-25.
[2]	ZHAO Yueqing, LIN Dezhi, CHEN Ping, TANG Jiali. Comparison and numerical simulation of single/double diaphragm forming of thermosetting carbon fiber prepreg [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(2): 109-118.
[3]	YAO Zhuojun, HAO Shang, LI Qianfu, YANG Zhengqiang, ZHANG Yanda, LIU Qianli. Preparation and properties of bisphenol M cyanate ester resin for hot melt prepreg [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(12): 49-53.
[4]	ZHAO Miao. Status and application in aerospace of advanced thermoplastic composite materials [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(12): 147-152.
[5]	ZHANG Xuewen, WANG Jihui, CHEN Hongda, NI Aiqing. Numerical modeling and optimisaition in thermo-stamping process of unidirectional fiber reinforced thermoplastic composites [J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(6): 104-114.
[6]	CHEN Boyi, QI Junwei, WANG Yuequan, SHI Jiaqi. Optimization and reconstruction of hat beam preforming mold based on advanced pultrusion process [J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(3): 59-67.
[7]	WANG Hua, WANG Xijie, SHI Hui, HAN Xiao. Effects of forming pressure on the properties of boron carbide/aramid ballistic insert plate [J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(3): 104-107.
[8]	LI Zhefu, LIU Weiping, SUN Baozhong, YUE Guangquan, TAN Yuan, ZHANG Jian. Investigation of the viscoelastic behavior in the hot press-forming process of uncured prepreg laminates [J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(2): 84-93.
[9]	LIU Xiao-fan, WU Shu-guang, XU Ren-xin. Properties of low temperature curing vinyl ester resin prepreg thickened by organic bentonite [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(8): 89-92.
[10]	MAN Jia-cheng, HOU Jin-sen, LI Zhe-fu, YUE Guang-quan, XU Peng, JIANG Bi-yu, LIU Wei-ping. Experimental study on compacting performance of continuous carbon fiber reinforced thermosetting prepreg [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(7): 45-51.
[11]	MAO Yi-mei, GUO Jian-jun, ZHENG Shi-hong, MAO Ya-sai. The study of the on-line prepreg pultrusion process of phenolic resin [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(6): 111-114.
[12]	JU Bo-wen, ZHANG Qi, ZHUANG Chun, WAN Li, HOU Jin-sen, HAO Xu-feng, WANG Xiao-lei, TIAN Jie. Research on advanced pultrusion technology for composite payload supported cabin stringer [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(4): 92-97.
[13]	YANG Ze-hao, TAO Lei, QI Liang-liang, LI Zhao-yang, LI Xin-he, DAI Jun, LIU Yong, ZHANG Hui. Design and performance research of carbon fiber reinforced epoxy resin prepreg tow for dry filament winding [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(3): 87-95.
[14]	ZHANG Yu-jie, YE Qi-fei, LIANG Yan-min, LIU Qi-bao, KE Chang-yi, YE Peng-hua. Study on double-vacuum curing technique for composite skins [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(9): 79-82.
[15]	WANG Min, LUAN Ying-wei, XU Peng, GAO Long-fei, WANG Shi-jie, LI Zhen-you. STUDY ON CURING BEHAVIOR OF X850 COMPOSITE MATERIAL DURING AUTOCLAVE PROCESS [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(2): 32-37.