THE PREPARATION OF 5228A EPOXY RESIN USED IN RFI AND THE IMPACTION ON MECHANICAL PROPERTY OF 5228A/CCF300 COMPOSITES

Abstract

Abstract: In this paper, the viscosity-temperature characteristics and formation property of 5228A epoxy resin used in RFI and the 5228A epoxy resin special used for prepreg are studied. Besides, the comparison of mechanical property between the two kinds of resins reinforced CCF300 composites are also studied. The results show that the 5228A epoxy resin system used in RFI which was prepared by proper modifying the formula of 5228A epoxy resin system special used for prepreg could meet the requirement of RFI. The impregnating-process temperature is 120~130℃ and the opening time is 60min. There are no obvious differences of the two kinds of resins reinforced CCF300 composites on the mechanical property.

Key words: 5228A epoxy resin, RFI, viscosity-temperature characteristics, mechanical property

CLC Number:

TB332

CHEN Wei, ZHANG Chen-qian, CHENG Li, LI Cha. THE PREPARATION OF 5228A EPOXY RESIN USED IN RFI AND THE IMPACTION ON MECHANICAL PROPERTY OF 5228A/CCF300 COMPOSITES[J]. COMPOSITES SCIENCE AND ENGINEERING, 2015, 0(5): 38-41.

References

[1] 益小苏. 先进复合材料技术研究与发展[M]. 北京:国防工业出版社,2006.
[2] 唐邦铭. 先进复合材料树脂膜渗透成形及其高性能化技术研究[D].北京:北京航空材料研究院,2005.
[3] 陈蔚, 成理, 张晨乾,等. CCF300/5228A复合材料RFI成型工艺参数[J].航空材料学报,2014,34(6):50-60.
[4] 蔡金刚. 碳纤维及复合材料发展情况[J]. 玻璃钢/复合材料,2011,(2):89-93.
[5] 刘哓蓓,王晓洁,惠雪梅.耐高温环氧树脂研究进展[J]. 玻璃钢/复合材料,2013,(3):118-121.
[6] 马立. RFI工艺成型碳NCF/环氧5228A复合材料研究[J]. 玻璃钢/复合材料,2008,(1):21-24.
[7] 张国利, 张鹏, 李嘉禄,等. RFI工艺用环氧树脂膜的制备及其化学流变特性[J]. 复合材料学报,2008,25(3):84-92.
[8] 唐邦铭,梁子青,等. 工艺因素对RFI复合材料渗透成型影响的试验研究[J]. 航空材料学报, 2008,28(3):57-61.
[9] 代晓青,谭艳,刘鈞. RFI工艺用环氧树脂基体研究[J]. 玻璃钢/复合材料,2006,(1):17-20.
[10] Loos A C. Low-cost fabrication of advanced polymeric composites by resin infusion process[J]. Advanced Composite Materials, 2001,10(2/3):99-106.
[11] Jens H, Cesar B. The challenge of reducing both airframe weight and manufacturing cost[J]. aircraft technologies structures, Air﹠Space Europe,2001,3(3/4):119-120.
[12] S. Amico , C. Lekakou. An experimental study of the permeability and capillary pressure in resin-transfer moulding[J]. Composites Science and Technology, 2001, (61): 1945-1959.
[13] Park, Moon Koo Kang. A numerical simulation of the resin film infusion process[J]. Composite Structures, 2003, 60: 432-437.
[14] 张秀艳,杨志忠,王春雨.树脂膜渗透(RFI)成型工艺及其应用[J]. 纤维复合材料,2004,1(2):39-41.
[15] Hsiao K T, Little R,Restrepo O,et al. A study of direct cure kinetics characterization during liquid composite molding[J]. Composites PartA, 2006, 37: 925-933.