RESEARCH OF HOT MOLDING PRESS ON LONG GLASS FIBER REINFORCED POLYPROPYLENE COMPOSITE

Abstract

Abstract: To improve the basic mechanical properties and the stability of mould pressed products formed by long glass fiber reinforced polypropylene (LGFRP), the hot molding process was subdivided into three parts: preheating process, moulding process and forming operation. And, the three parts contain seven parameters which were studied with the orthogonal test and single factor test method .The effect of the seven parameters on the mechanical properties of mould pressed products prepared from LGFRP composite material was discussed and analyzed, and the better molding process parameters are optimized. The results show that the effect of process parameters on mechanical properties is influenced by processing conditions, and refine of the molding process can improve the basic mechanical properties of mould pressed products, and enhance the stability of moulding process.

Key words: long glass fiber reinforced polypropylene, hot molding process, process parameters, mechani-cal properties

CLC Number:

TB332

TANG Rong-hua, YANG Xu-jing, ZHENG Juan. RESEARCH OF HOT MOLDING PRESS ON LONG GLASS FIBER REINFORCED POLYPROPYLENE COMPOSITE[J]. Fiber Reinforced Plastics/Composites, 2016, 0(8): 62-67.

References

[1] Lyu M Y, Choi T G. Research trends in polymer materials for use in lightweight vehicles [J]. International Journal of Precision Engineering and Manufacturing, 2015, 16(1): 213-220.
[2] 宋传江, 王虎. 玻璃纤维增强复合材料工程化应用进展[J]. 中国塑料, 2015(3): 9-15.
[3] 王汝敏, 郑水蓉, 郑亚萍. 聚合物基复合材料及工艺[M]. 北京:科学出版社, 2004.
[4] Wakeman M D, Cain T A, Rudd C D, et al. Compression moulding of glass and polypropylene composites for optimized macro-and micro-mechanical properties II. Glass-mat-reinforced thermoplastics[J]. Composites Science and Technology, 1999(59): 709-726.
[5] 王秋峰,周晓东,侯静强. 长纤维增强热塑性复合材料的浸渍技术与成型工艺[J]. 纤维复合材料, 2006(2): 43-46.
[6] 崔萍, 楚晓, 艾宏玲, 等. 聚丙烯/亚麻纤维复合材料的成型工艺及力学性能研究[J]. 工程塑料应用, 2010(4): 43-46.
[7] Rubio A, Eguizabal P, Mendizabal M A, et al. Influence of the processing parameters on glass mat reinforced thermoplastic (GMT) stamping [J]. Composites Manufacturing, 1992, 3(1): 47-52.
[8] 张广平, 俞建勇, 戴干策. 操作参数对玻纤毡增强复合材料流动成型的影响[J]. 塑料工业, 2003(8): 32-34.
[9] 代汉达, 曲建俊, 庄乾兴. 模压工艺对CF+G/PEE复合材料力学性能的影响[J]. 吉林大学学报(工学版), 2010, 40(2): 457-460.
[10] 沃西源, 薛芳, 李静. 复合材料模压成型的工艺特性和影响因素分析[J]. 高科技纤维与应用, 2009(6): 41-44.
[11] 胡章平. 长玻纤增强聚丙烯复合材料模压成型工艺研究[D]. 长沙: 湖南大学, 2015.
[12] 李敏, 张佐光, 李艳霞, 等. 复合材料层板热压工艺参数的分析与优化[J]. 材料工程, 2007(1): 106-110.
[13] 路慧玲, 黄进, 戴干策. 过程参数对GMT片材熔融浸渍的影响[J]. 华东理工大学学报, 2001(2): 16-19.
[14] 路慧玲, 朱永全, 戴干策. PP /GMT制品模内冷却与结晶过程模拟[J]. 复合材料学报, 2002(1): 17-21.
[15] 王瑞, 王春红. 竹纤维增强聚丙烯复合材料的制备及其性能研究[J]. 中国塑料, 2006(10): 43-46.