Study on the properties of carbon fiber surface coatings peeled by CO2 laser

doi:10.19936/j.cnki.2096-8000.20220128.005

Abstract

Abstract: Carbon fiber composite material (CFRP) is widely used in the manufacture of aircraft structures and components in the aviation field. Because aircraft often works in some harsh conditions, the surface coating of carbon fiber will age and lose its original performance. The longer the aircraft is in service, the deeper the coating needs to be removed. The coating of CFRP was quantitatively peeled by CO₂ laser instead of the traditional mechanical grinding. The experimental results show that the preset requirements of 5 μm, 10 μm and 20 μm removal can be achieved under the power of 20 W, 25 W and 30 W, within a certain error permissible range. In addition, the mechanical properties of the material are not weakened, which meet the requirements of recoating.

Key words: laser peeling, laser parameters, carbon fiber composites, surface treatment

CLC Number:

TB332

DU Hong-yu, CHENG Jian, LIU Dun, LI Zi-wen, FENG Kai. Study on the properties of carbon fiber surface coatings peeled by CO₂ laser[J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(1): 36-41.

References

[1] 侯进森, 冯奇, 杨琨, 等. 表面处理对碳纤维复合材料胶接性能影响研究[J]. 上海汽车, 2017(10): 50-53.
[2] 谢薇. 可供选择的碳纤维复合材料(CFRP)表面处理方法:用于粘接以替代手工打磨[J]. 玻璃钢, 2008(3): 46-48.
[3] 徐世珍, 窦红强, 韩丰明, 等. K9玻璃表面颗粒污染物的激光剥离[J]. 实验室研究与探索, 2017, 36(6): 5-8, 17.
[4] 宋峰, 刘淑静, 牛孔贞, 等. 激光清洗原理与应用研究[J]. 清洗世界, 2005, 21(1): 1-6.
[5] 俞鸿斌, 王春明, 王军, 等. 碳钢表面激光除锈研究[J]. 应用激光, 2014, 34(4): 310-314.
[6] 俞鸿斌. 金属表面激光剥离技术研究[D]. 武汉: 华中科技大学, 2015.
[7] 陈林, 杨永强. 激光清洁技术及其应用[J]. 红外与激光工程, 2004, 33(3): 274-277.
[8] WANG Z, ZENG X, HUANG W. Parameters and surface performance of laser removal of rust layer on A3 steel[J]. Surface & Coatings Technology, 2003, 166(1): 10-16.
[9] WOLFGANG K, SIMONE P, PASCALE R, et al. Laser interaction with coated collagen and cellulose fibre composites: Fundamentals of laser cleaning of ancient parchment manuscripts and paper[J]. Applied Surface Science, 1998, 127-129: 746-754.
[10] FISCHER F, KRELING S, DILGER K. Surface structuring of CFRP by using modern excimer laser sources[J]. Physics Procedia, 2012, 39: 154-160.
[11] LAMBIASE F, GENNA S, LEONE C, et al. Laser-assisted direct-joining of carbon fibre reinforced plastic with thermosetting matrix to polycarbonate sheets[J]. Optics & Laser Technology, 2017, 94: 45-58.
[12] NAGESH S, MURTHY H N, PAL R, et al. Investigation of the effect of nanofillers on the quality of CO₂ laser cutting of FRP nanocomposites[J]. The International Journal of Advanced Manufacturing Technology, 2017, 90(5-8): 2047-2061
[13] KASPAR J, HFELE T, KALDENHOFF C, et al. Hybrid additive design of FRP components-fiber-reinforced sandwich structures based on selective laser sintering technology[J]. Procedia CIRP, 2017, 60: 235-240.
[14] KOHZAKI S, NAKANISHI E, SAWAKI Y, et al. YAG laser drilling of aramid FRP laminates[J]. Advances in non-traditional machining, 2005, 2: 583-588.
[15] CHOUDHURY I A, CHUAN P C. Experimental evaluation of laser cut quality of glass fibre reinforced plastic composite[J]. Optics & Lasers in Engineering, 2013, 51(10): 1125-1132.
[16] PATHIK P, SAURIN S, TEJAS P. Experimental analysis and ANN modelling of HAZ in laser cutting of glass fibre reinforced plastic composites[J]. Procedia Technology, 2016, 23: 406-413.
[17] CANEL T, BAGˇLAN I, SINMAZCELIK T. Mathematical modelling of laser ablation of random oriented short glass fiber reinforced Polyphenylene sulphide (PPS) polymer composite[J]. Optics & Laser Technology, 2019, 115: 481-486.
[18] ELTAWAHNI H A, OLABI A G, BASMAGE O M, et al. CO₂ laser cutting of glass fiber-reinforced plastics[J]. Encyclopedia of Renewoble and Sustainable Materials, 2020, 1: 145-159.
[19] DHAKAL H N, ZHANG Z Y, BENNETT N, et al. Low-velocity impact response of non-woven hemp fibre reinforced unsaturated polyester composites: Influence of impactor geometry and impact velocity[J]. Composite Structures, 2012, 94(9): 2756-2763.
[20] LAMBIASE F, GENNA S, LEONE C, et al. Laser-assisted direct-joining of carbon fibre reinforced plastic with thermosetting matrix to polycarbonate sheets[J]. Optics & Laser Technology, 2017, 94: 45-58.
[21] 刘静, 曹意林, 李刚, 等. 激光对碳纤维及碳纤维/环氧树脂复合材料性能影响[J]. 复合材料学报, 2018, 35(11): 2979-2986.
[22] NATTAPAT M, MARIMUTHU S, KAMARA A M, et al. Laser surface modification of carbon fiber reinforced composites[J]. Materials and Manufacturing Processes, 2015, 30(12): 1450-1456.
[23] ESFAHANI M N, COUPLAND J, MARIMUTHU S. Microstructure and mechanical properties of a laser welded low carbon-stainless steel joint[J]. Journal of Materials Processing Technology, 2014, 214(12): 2941-2948.
[24] 贾宝申, 唐洪平, 苏春洲, 等. 脉冲激光去除树脂基复合材料表面涂层[J]. 中国激光, 2019, 46(12): 133-140.

Study on the properties of carbon fiber surface coatings peeled by CO₂ laser

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	WANG Wenqian, FENG Yu, LI Zhe, LIU Songjing, AN Tao, WANG Yitao, LI Yuankai. Simulation of temperature field distribution of carbon fiber composites under laser irradiation [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(7): 5-15.
[2]	TIAN Huifang, LIU Jiao, WU Yingfeng. Design and analysis of surface treatment device for filament wound plastic liner [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(2): 96-101.
[3]	XU Quanwei, GUO Xiaofeng, QIAO Shujie, LI Siqing, CHE Jiangning. Prediction of the ultimate loads and structural optimization design for the wind turbine blades with glass-carbon laminate based on neural network [J]. COMPOSITES SCIENCE AND ENGINEERING, 2024, 0(12): 69-74.
[4]	YANG Weiya, GAO Dongchen, TIE Ying, ZHANG Zhenzhen, GE Chaokun. Study on interlaminar fracture toughness of self-healing composites based on multi-scale analysis [J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(9): 29-35.
[5]	CAO Yuhan, GUO Shuhan, OUYANG Junjie, KONG Fanqi, WANG Fusheng. Research of the influence of high temperature pre-damage on the residual strength after impact of carbon fiber composites [J]. COMPOSITES SCIENCE AND ENGINEERING, 2023, 0(6): 30-36.
[6]	XIONG Hua-kun, YUAN Guo-qing, YANG Jia-yong, QIU Xue-shi. Study on laser treatment of quartz fiber/cyanate ester resin composite bonding surfaces [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(4): 81-86.
[7]	LIN Zai-wei, YUAN Guo-qing. Experimental study of the deformation performance of composite beams with SMA sheet actuators adhered on the surface [J]. COMPOSITES SCIENCE AND ENGINEERING, 2022, 0(3): 81-86.
[8]	SUN Yu, LIU Qiang, HUANG Feng, MA Jin-rui, ZHANG Yu. STUDY ON BONDING TECHNOLOGY OF TITANIUM ALLOY TRIM/COMPOSITE FAN BLADE [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(3): 78-81.
[9]	WU Bo, YANG Chang-ling, ZHANG lin-ping, LU Yong-gen. RESEARCH PROGRESS ON INTERFACIAL PROPERTIES OF CARBON FIBER REINFORCED POLYPHENYLENE SULFIDE COMPOSITES [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(3): 117-121.
[10]	SUN Kun, ZHAO Wen-zhong, ZHANG Chen-hui, LIU Ming-chang, LI Jian-wei, GAO Qi, XU Pei-lun. Optimization of forming process and supporting materials of domestic carbon fiber prepreg for radar antenna [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(12): 66-72.
[11]	LI Meng-ying, XIAO Jun, HUAN Da-jun, WANG Xing-bang, YANG Xiao, JIAO Yang. Microwave curing process and properties of T700/epoxy composites by wet filament lamination winding [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(12): 89-94.
[12]	HU Bin-bin, WANG Shao-fei, CAI Chao-qian, HUANG Zhuang, MA Yu, ZHANG Hui. Effect of carbon fiber surface treatment on the mechanical properties of liquid-formed carbon fiber reinforced MC nylon composite [J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(10): 83-88.
[13]	ZHANG Qi, WEI Zhen-hai, LIU Qian-li, XU Xiao-kui. PREPARATION AND PROPERTIES OF HIGH TEMPERATURE RESISTANT RESIN SYSTEM FOR HOT PRESSURE TANK INITIAL PRESSURE PROCESSING PREPREG [J]. Composites Science and Engineering, 2020, 0(8): 76-82.
[14]	GUO Xiao-feng, QI Jian-feng, HUANG Xin-xiang. STRUCTURAL DESIGN OPTIMIZATION AND PERFORMANCE ANALYSIS OF GLASS-CARBON HYBRID LOW WIND SPEED WIND TURBINE BLADES [J]. Composites Science and Engineering, 2020, 0(6): 25-29.
[15]	FU Wen-qiang, WANG Xiao-bing, WANG Bao-chun, XU Hong-min. RESEARCH PROGRESS ON ADHESION SYSTEM OF RESIN-BASED COMPOSITES AND METAL MATERIALS [J]. Composites Science and Engineering, 2020, 0(6): 121-128.