A review about drilling of CFRP

doi:10.19936/j.cnki.2096-8000.20211228.019

Abstract

Abstract: Carbon fiber reinforced plastic(CFRP) composites are widely used in aero engine nacelles for its exellent mechanical properties. The material inevitably requires a lot of connection, but it is a brittle material and anisotropic. After drilling, the stress concentration of the material will have a certain of defects. In order to explore the impact of drilling on the quality of the hole, a lot of researches have been carried out on its drilling process at home and abroad, its process includes three phenomen i.e., a chip formation mechanism, drilling force, drilling heat. Based on the research results from all over the world, this article comprehensively summarizes the drilling mechanism of CFRP, explains the types of defects in the hole after drilling and the development of the drilling process of carbon fiber composite materials.

Key words: carbon fiber, composite material, machining of drilling, defects

CLC Number:

TB332

ZHANG Yue-xin, YANG Ming-jun, LIU Geng, WANG Chong-jie. A review about drilling of CFRP[J]. COMPOSITES SCIENCE AND ENGINEERING, 2021, 0(12): 120-128.

References

[1] 于海宁, 高长星, 王艳华. 碳纤维增强树脂基复合材料的应用及展望[J]. 合成纤维工业, 2020, 43(1): 55-59.
[2] KHADKA A, SUBESHAN B, ASMATULU R. Correction to: Studies on de-icing and anti-icing of carbon fiber-reinforced composites for aircraft surfaces using commercial multifunctional permanent superhydrophobic coatings[J]. Journal of Materials Science, 2021, 56(5): 4051-4051.
[3] 邢丽英, 冯志海, 包建文, 等. 碳纤维及树脂基复合材料产业发展面临的机遇与挑战[J]. 复合材料学报, 2020, 37(11): 50-56.
[4] 钱伯章. 碳纤维与中国制造2025[J]. 合成纤维, 2020, 49(2): 56-57.
[5] 林德春, 潘鼎, 高健, 等. 碳纤维复合材料在航空航天领域的应用[J]. 玻璃钢, 2007(1): 18-28.
[6] SINGH A P, SHARMA M, SINGH I. A review of modeling and control during drilling of fiber reinforced plastic composites[J]. Composites Part B: Engineering, 2013, 47: 118-125.
[7] SHYHA I, SOO S L, ASPINWALL D, et al. Effect of laminate configuration and feed rate on cutting performance when drilling holes in carbon fibre reinforced plastic composites[J]. Journal of materials processing technology, 2010, 210(8): 1023-1034.
[8] 陈俊涛. 碳纤维增强复合材料在高低周载荷下的疲劳行为研究[D]. 哈尔滨: 哈尔滨工业大学, 2017.
[9] 苏飞, 陈娟, 邱新义, 等. CFRP钻削制孔分层的形态研究 [J]. 宇航材料工艺, 2018, 48(5): 78-82.
[10] PERSSON E, ERIKSSON I, ZACKRISSON L. Effects of hole machining defects on strength and fatigue life of composite laminates[J]. Composites Part A: Applied Science and Manufacturing, 1997, 28(2): 141-151.
[11] CAPELLO E, TAGLIAFERRI V. Drilling damage of GFRP and residual mechanical behavior-part Ⅱ: Static and cyclic bearing loads[J]. Journal of Composites, Technology and Research, 2001, 23(2): 131-137.
[12] HOCHENG H, CHEN C, TSAO C. Prediction of critical thrust force for tubular composite in drilling-induced delamination by numerical and experimental analysis[J]. Composite Structures, 2018, 203(5): 66-73.
[13] HOCHENG H, TSAO C. The path towards delamination-free drilling of composite materials[J]. Journal of Materials Processing Technology, 2005, 167(2-3): 251-264.
[14] MATHEW J, RAMAKRISHNAN N, NAIK N. Investigations into the effect of geometry of a trepanning tool on thrust and torque during drilling of GFRP composites[J]. Journal of Materials Processing Technology, 1999, 91(1-3): 1-11.
[15] BHATNAGAR N, RAMAKRISHNAN N, NAIK N, et al. On the machining of fiber reinforced plastic(FRP) composite laminates[J]. International Journal of Machine Tools and Manufacture, 1995, 35(5): 701-716.
[16] CHANG C S. Turning of glass-fiber reinforced plastics materials with chamfered main cutting edge carbide tools[J]. Journal of Materials Processing Technology, 2006, 180(1-3): 117-129.
[17] 鲍永杰, 高航, 李凤全. 电镀金刚石钻头钻削碳纤维复合材料研究[J]. 金剛石與磨料磨具工程, 2009(3): 38-42.
[18] 张厚江. 单向碳纤维复合材料直角自由切削力的研究 [J]. 航空学报, 2005, 26(5): 604-609.
[19] 韩胜超, 陈燕, 徐九华, 等. 多齿铣刀侧铣加工多层CFRP铣削力的建模与仿真[J]. 复合材料学报, 2014, 31(5): 1375-1381.
[20] 蔡晓江. 基于复合材料各向异性的切削力热变化规律和表面质量评价试验研究[D]. 上海: 上海交通大学, 2014.
[21] YASHIRO T, OGAWA T, SASAHARA H. Temperature measurement of cutting tool and machined surface layer in milling of CFRP[J]. International Journal of Machine Tools and Manufacture, 2013, 70: 63-69.
[22] BRINKSMEIER E, FANGMANN S, RENTSCH R. Drilling of composites and resulting surface integrity[J]. CIRP Annals, 2011, 60(1): 57-60.
[23] SREEJITH P, KRISHNAMURTHY R, MALHOTRA S, et al. Evaluation of PCD tool performance during machining of carbon/phenolic ablative composites[J]. Journal of Materials Processing Technology, 2000, 104(1-2): 53-58.
[24] MERINO-PÉREZ J L, ROYER R, AYVAR-SOBERANIS S, et al. On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part Ⅰ: Workpiece constituents, cutting speed and heat dissipation[J]. Composite Structures, 2015, 123(16): 1-8.
[25] CHEN W C. Some experimental investigations in the drilling of carbon fiber-reinforced plastic (CFRP) composite laminates[J]. International Journal of Machine Tools and Manufacture, 1997, 37(8): 1097-1108.
[26] SAKAMOTO S, IWASA H. Effect of cutting revolution speed on cutting temperature in helical milling of CFRP composite laminates[J]. Key Engineering Materials, 2012, 523-524: 58-63.
[27] 孙剑飞, 刘峰, 陈五一, 等. 高模量树脂基碳纤维复合材料钻孔加工缺陷分析[J]. 金属加工(冷加工), 2016(9): 21-24.
[28] DURAO L, MAGALHAES A, MARQUES A, et al. Effect of drilling parameters on composite plates damage[C]//Tavares International Conference HSIMP 2007-High Speed Industrial Manufacturing Processes. France: 2007: 1-8.
[29] 张厚江, 陈五一, 陈鼎昌. 碳纤维复合材料钻孔分层的渗透检测[J]. 航空制造技术, 2004, 12: 78-80.
[30] HO-CHENG H, DHARAN C. Delamination during drilling in composite laminates[J]. Journal of Engineering for Industry, 1990, 112(3): 236-239.
[31] SEIF M A, KHASHABA U A, ROJAS-OVIEDO R. Measuring delamination in carbon/epoxy composites using a shadow moiré laser based imaging technique[J]. Composite Structures, 2007, 79(1): 113-118.
[32] GENG D, LIU Y, SHAO Z, et al. Delamination formation, evaluation and suppression during drilling of composite laminates: a review[J]. Composite Structures, 2019, 216: 168-186.
[33] HOCHENG H, TSAO C. Effects of special drill bits on drilling-induced delamination of composite materials[J]. International Journal of Machine Tools and Manufacture, 2006, 46(12-13): 1403-1416.
[34] JAIN S, YANG D. Effects of feedrate and chisel edge on delamination in composites drilling[J]. Journal of Manufacturing Science and Engineering, 1993, 115(4): 398-405.
[35] JAIN S, YANG D C. Delamination-free drilling of composite laminates[J]. Journal of Engineering for Industry, 1994, 116(4): 475-481.
[36] 汪海晋. 树脂基复合材料钻削缺陷产生机理与控制策略研究[D]. 济南: 山东大学, 2016.
[37] 张厚江, 陈五一, 陈鼎昌. 碳纤维复合材料(CFRP)孔壁的微观形态[J]. 复合材料学报, 2000, 17(2): 98-101.
[38] 张厚江. 碳纤维复合材料(CFRP)钻削加工技术的研究[D]. 北京: 北京航空航天大学, 1998.
[39] 贺虎. 碳纤维复合材料钻削力与孔质量研究[D]. 南京: 南京航空航天大学, 2011.
[40] GHIDOSSI P, MANSORI M E, PIERRON F. Influence of specimen preparation by machining on the failure of polymer matrix off-axis tensile coupons[J]. Composites Science and Technology, 2006, 66(11-12): 1857-1872.
[41] AROLA D, MCCAIN M. Surface texture and the stress concentration factor for FRP components with holes[J]. Journal of Composite materials, 2003, 37(16): 1439-1460.
[42] AL-WANDI S, DING S, MO J. An approach to evaluate delamination factor when drilling carbon fiber-reinforced plastics using different drill geometries: Experiment and finite element study[J]. The International Journal of Advanced Manufacturing Technology, 2017, 93(9): 4043-4061.
[43] AMEUR M, HABAK M, KENANE M, et al. Machinability analysis of dry drilling of carbon/epoxy composites: Cases of exit delamination and cylindricity error[J]. The International Journal of Advanced Manufacturing Technology, 2017, 88(9-12): 2557-2571.
[44] WANG X, SHEN X, ZENG C, et al. Combined influences of tool shape and as-deposited diamond film on cutting performance of drills for CFRP machining[J]. Surface and Coatings Technology, 2018, 347: 390-397.
[45] MONTOYA M, CALAMAZ M, GEHIN D, et al. Evaluation of the performance of coated and uncoated carbide tools in drilling thick CFRP/aluminium alloy stacks[J]. The International Journal of Advanced Manufacturing Technology, 2013, 68(9-12): 2111-2120.
[46] ILIESCU D, GEHIN D, GUTIERREZ M, et al. Modeling and tool wear in drilling of CFRP[J]. International Journal of Machine Tools and Manufacture, 2010, 50(2): 204-213.
[47] DURÃO L M P, GONÇALVES D J, TAVARES J M R, et al. Drilling tool geometry evaluation for reinforced composite laminates[J]. Composite Structures, 2010, 92(7): 1545-1550.
[48] HEISEL U, PFEIFROTH T. Influence of point angle on drill hole quality and machining forces when drilling CFRP[J]. Procedia Cirp, 2012, 1(7): 471-476.
[49] FEITO N, DÍAZ-ÁLVAREZ J, LÓPEZ-PUENTE J, et al. Experimental and numerical analysis of step drill bit performance when drilling woven CFRPs[J]. Composite Structures, 2018, 184: 1147-1155.
[50] FEITO N, ÁLVAREZ J D, CANTERO J, et al. Influence of special tool geometry in drilling woven CFRPs materials[J]. Procedia engineering, 2015, 132: 632-638.
[51] DANDEKAR C R, SHIN Y C. Modeling of machining of composite materials: a review[J]. International Journal of Machine tools and manufacture, 2012, 57: 102-121.
[52] CHE D, SAXENA I, HAN P, et al. Machining of carbon fiber reinforced plastics/polymers: A literature review[J]. Journal of Manufacturing Science and Engineering, 2014, 136(3): 34001-34001.
[53] DURAO L, DE MOURA M, MARQUES A T. Numerical simulation of the drilling process on carbon/epoxy composite laminates [J]. Composites Part A: Applied Science and Manufacturing, 2006, 37(9): 1325-1333.
[54] MACKERLE J. Finite element analysis and simulation of machining:An addendum: A bibliography(1996-2002)[J]. International Journal of Machine Tools and Manufacture, 2003, 43(1): 103-114.