丝束变角度层合板频率性能的参数化分析与优化

玻璃钢/复合材料 ›› 2016, Vol. 0 ›› Issue (8): 27-32.

丝束变角度层合板频率性能的参数化分析与优化

孙士平, 邓同强, 胡政

南昌航空大学航空制造工程学院,南昌330063

收稿日期:2016-03-21 出版日期:2016-08-28 发布日期:2016-08-28
作者简介:孙士平(1972-),男,博士,副教授,主要从事材料/结构的拓扑优化设计研究,shipingsun@163.com。
基金资助:
国家自然科学基金项目(11362017)

PARAMETRIC ANALYSIS AND OPTIMIZATION OF FREQUENCY PROPERTY OF VARIABLE ANGLE TOW LAMINATES

SUN Shi-ping, DENG Tong-qiang, HU Zheng

School of Aeronautical Manufacturing Engineering, Nanchang Hangkong University, Nanchang 330063, China

Received:2016-03-21 Online:2016-08-28 Published:2016-08-28

摘要/Abstract

摘要： 为有效设计丝束变角度(VAT)层合板的频率性能,首先基于纤维方向角的线性变化定义建立了VAT层合板参数化有限元模型,开展了VAT层合板频率性能的参数化研究;其次,基于纤维轨迹的周期性特征,对比分析了VAT层合板不同长宽比和厚度对频率性能的影响;最后,结合序列响应面方法,完成了不同边界下最优化VAT层合板频率特性的纤维轨迹参数设计。计算结果表明,VAT层合板的一阶频率基本不受纤维参考方向角影响,而优化纤维参考方向角能有效提高一二阶频率带隙;特征长度对频率特性的影响随长宽比增大而衰减;越薄的VAT层合板其频率特性受纤维轨迹的影响越大。研究结果为VAT层合板的频率性能设计提供了参考。

关键词: 丝束变角度层合板, 频率优化, 纤维轨迹, 响应面方法

Abstract: The aim of this paper is to trace the influence of fiber path parameters on frequency property so as to design VAT laminates effectively. Firstly, the parametric finite element model of VAT laminate was established to investigate effect of path parameters on the frequency property, by utilizing the definition of linear variation of fiber angle. Secondly, influences of aspect ratio and thickness of VAT laminate on frequency characteristic were analyzed and discussed based on the periodical distribution of fiber path. Finally, optimization design fiber path of square VAT laminate was conducted under different boundary conditions using sequential response surface method, for maximizing the first order frequency and the difference of first and second order frequency. The results show that the band gap of first and second order frequency of VAT laminates can be effectively improved by the optimization of fiber reference direction angle, which has little influence on the first order frequency. Effect of characteristic length on frequency performance is decreasing with increasing aspect ratio. The thinner VAT laminates, the greater the impact of fiber path on frequency performance. The results provide guidance for frequency performance design of VAT laminates.

Key words: variable angle tow laminate, frequency optimization, fiber path, response surface method

中图分类号:

TB332

孙士平, 邓同强, 胡政. 丝束变角度层合板频率性能的参数化分析与优化[J]. 玻璃钢/复合材料, 2016, 0(8): 27-32.

SUN Shi-ping, DENG Tong-qiang, HU Zheng. PARAMETRIC ANALYSIS AND OPTIMIZATION OF FREQUENCY PROPERTY OF VARIABLE ANGLE TOW LAMINATES[J]. Fiber Reinforced Plastics/Composites, 2016, 0(8): 27-32.

参考文献

[1] 秦永利. 纤维曲线铺放制备变刚度复合材料层合板的研究进展[J]. 玻璃钢/复合材料, 2012(1): 61-66.
[2] Hyer M W, Charette R F. Use of curvilinear fiber format in composite structure design[J]. AIAA Journal, 1991, 29(6): 1011-1015.
[3] Gürdal Z, Olmedo R. In-plane response of laminates with spatially varying fiber orientations: variable stiffness concept[J]. AIAA Journal, 1993, 31(4): 751-758.
[4] Waldhart C. Analysis of tow-placed variable-stiffness laminates[D].Blacksburg, VA: Vir-ginia Polytechnic Institute and State University, 1996.
[5] Jegley D C, Tatting B F, Gürdal Z. Tow-steered panels with holes subjected to compression or shear loading: Proceedings of the 46th AIAA/ASME/ AHS/ASC structures, structural dynamics and materials(SDM) conference[C]. Austin, TX, USA: AIAA, 2005.
[6] Lopes C S, Gürdal Z, Camanho P P. Variable stiffness composite panels: buckling and first-ply failure improvements over straight fibre laminates[J]. Comput. Struct., 2008, 86: 897-907.
[7] Gürdal Z, Tatting B F, Wu C K. Variable stiffness composite panels: effects of stiffness variation the in-plane and buckling response[J]. Composites Part A: Applied Science and Manufacturing, 2008, 39: 911-922.
[8] Wu Z M, Weaver P M, Raju G, et al. Buckling analysis and optimisation of variable angle tow composite plates[J]. Thin-Walled Structures, 2012,60: 163-172.
[9] Alhajahmad A, Abdalla MM, Gürdal Z. Optimal design of tow-placed fusedlage panels for maximum strength with buckling considerations[J]. Journal of Aircraft, 2010, 47(3): 775-782.
[10] Liu W L, Butler R. Buckling optimization of variable angle tow panels using the infinite strip method[J]. AIAA Journal, 2013, 51(6): 1442-1449.
[11] Groh RMJ, Weaver PM. Buckling analysis of variable angle tow, variable thickness panels with transverse shear effects[J]. Computer Structures, 2014,107: 482-493.
[12] 马永前. 纤维曲线铺放的变刚度复合材料层合板的屈曲[J]. 玻璃钢/复合材料, 2009(5):31-35.
[13] 杜宇, 杨涛, 李志猛, 等. 纤维曲线铺放的变刚度复合材料层合板的失效分析[J]. 宇航材料工艺, 2013, 5: 22-25.
[14] 杜宇, 杨涛, 戴维蓉, 等. 纤维曲线铺放的变刚度复合材料损伤失效试验研究[J]. 固体火箭技术, 2013, 36(6): 826-830.
[15] 杨竣博, 宋笔锋, 钟小平. 丝束变角度层合板屈曲性能的有限元分析[J]. 复合材料学报, 2014, 31(4): 991-997.
[16] 杨竣博, 宋笔锋, 钟小平. 丝束变角度层合板屈曲性能的参数化研究[J]. 复合材料学报, 2015,32(4): 1145-1152.
[17] Honda S, Narita Y, Sasaki K. Discrete Optimization for Vibration Design of Composite Plates by Using Lamination Parameters[J]. Advanced Composite Materials, 2009, 18: 297-314.
[18] Akhavan H, Ribeiro P. Natural modes of vibration of variable stiffness composite laminates with curvilinear fibers[J]. Composite Structures, 2011,93: 3040-3047.
[19] 孙士平, 胡坚堂. 基于均匀设计序列响应面法的开孔圆柱壳屈曲优化[J]. 计算机辅助设计与图形学学报, 2016, 28(1): 146-154.