铺层方向角偏差对复合材料层板阶梯挖补的拉伸强度影响研究

复合材料科学与工程 ›› 2015, Vol. 0 ›› Issue (4): 52-56.

铺层方向角偏差对复合材料层板阶梯挖补的拉伸强度影响研究

刘国春¹, 幸李雯², 杨文锋¹, 张吉武¹

1.中国民用航空飞行学院航空工程学院,广汉618307;
2.中国民用航空飞行学院绵阳分院,绵阳621000

收稿日期:2014-11-21 出版日期:2015-04-28 发布日期:2021-09-14
作者简介:刘国春(1983-),男,硕士,讲师,主要从事复合材料结构设计与维修分析研究,liuguochun@cafuc.edu.cn。本文作者还有唐庆如¹。
基金资助:
国家自然科学基金民航联合基金重点项目(U1233202);民航局重大专项科技项目(MHRD201240)

THE EFFECT OF PLY ANGLE DECLINATION ON TENSILE STRENGTH OF COMPOSITE STEP-LAP REPAIR

LIU Guo-chun¹, XING Li-wen², YANG Wen-feng¹, ZHANG Ji-wu¹

1. Aviation Engineering Institute, Civil Aviation Flight University of China, Guanghan 618307, China;
2. Mianyang Sub-College, Civil Aviation Flight University of China, Mianyang 621000, China

Received:2014-11-21 Online:2015-04-28 Published:2021-09-14

摘要/Abstract

摘要： 针对复合材料损伤结构维修中容易出现的铺层角度偏差,根据实际维修情况建立复合材料层板阶梯挖补结构的有限元计算模型,并通过试验验证了该模型的准确性。基于该有限元分析模型并考虑真实维修过程中可能出现的铺叠误差与基准偏差,分别进行了维修结构的单层与整体铺层方向角偏移的拉伸强度性能分析。结果表明,补片出现小角度方向角偏移时,补片中面层以下的铺层角偏移对于拉伸强度的影响可以忽略,中面层以上的铺层随着偏移角度的增大与越靠近表层的位置,结构整体极限应力逐渐增大,当最表层铺层出现偏移时,对于修补结构拉伸强度的影响较大;附加层在修补结构中受载严重,通用的0°附加层铺设角度不一定适用于所有的修补工况,该分析结论也为实际工程维修提供了很好的指导意义。

关键词: 铺层偏差, 阶梯挖补, 复材维修, 模型验证

Abstract: According to ply angle declination of composite repair, a three dimensional finite element analysis model is developed for the composite laminated plates with a step-lap repair, which conforms with the results of experiments. Both single ply declination and total plies declination were calculated for the deviation of laying and benchmark. The result of calculations shows that few effects on tensile strength that the declinate ply is under middle plane. The larger angle declination and the position more close to the top ply, the stress level of whole structure is lager. The most serious case occurs on when the angle declination of top ply. The additional ply affords much more loads, and the general 0° angle may not fit for all the repair cases. The conclusion has great significance in directing the engineering practice of composite repair.

Key words: ply angle declination, step-lap repair, composite repair, model verification

中图分类号:

TB332

刘国春, 幸李雯, 杨文锋, 张吉武. 铺层方向角偏差对复合材料层板阶梯挖补的拉伸强度影响研究[J]. 复合材料科学与工程, 2015, 0(4): 52-56.

LIU Guo-chun, XING Li-wen, YANG Wen-feng, ZHANG Ji-wu. THE EFFECT OF PLY ANGLE DECLINATION ON TENSILE STRENGTH OF COMPOSITE STEP-LAP REPAIR[J]. COMPOSITES SCIENCE AND ENGINEERING, 2015, 0(4): 52-56.

参考文献

[1] 中国航空研究院. 复合材料结构设计手册[M]. 北京: 航空工业出版社, 2001.
[2] Chun H Wang, Andrew J Gunnion. On the design methodology of scarf repairs to composite laminates[J]. Composites Science and Technology, 2008,68(1): 35-46.
[3] Baker A.A. Development of a hard-patch approach for scarf repair of composite structure[C]. Defense Science and Technology Organization Report TR-1892, 2006.
[4] Baker AA. Joining and repair of aircraft composite structures[M]. Composite engineering handbook. New York: Marcel Dekker, 1997.
[5] 喻梅. 复合材料结构挖补补强强度研究[D]. 南京: 南京航空航天大学, 2005.
[6] 徐建新, 张志德, 李顶河. 复合材料层合板阶梯式挖补修理参数分析[J]. 机械科学与技术,2011,30(8):1304-1307.
[7] 徐建新,曹小梅,李顶河. 复合材料加筋板的阶梯式挖补修理稳定性分析[J]. 中国民航大学学报,2011,29(4):1-3,19.
[8] Ali Al-Mansour,程小全,寇长河. 单面贴补修理后层合板的拉伸性能[J]. 复合材料学报,2005,22(3):140-144.
[9] 孟凡颢, 陈绍杰, 童小燕. 层压板修理设计中的参数选择问题[J]. 复合材料学报,2001,18(4):123-127.
[10] 陈光伟,王富有,张国利,等. 阶梯型对接层合板复合材料力学性能的试验研究[J].材料工程,2009,S2: 182-185.
[11] 戴棣. 复合材料结构件的固化变形研究[D]. 南京: 南京航空航天大学,1999.
[12] 卞航, 粱宪珠, 张铖, 等. 铺层角度偏差对曲面复合材料结构固化变形的影响分析[J]. 材料开发与应用,2012,27(4):38-41.
[13] 沈观林, 胡更开. 复合材料力学[M]. 北京:清华大学出版社, 2006.
[14] 郭霞,关志东,刘遂,等. 层压板双面挖补修理的拉伸性能研究及参数分析[J]. 复合材料学报,2012,29 (1):176-182.