PREPARATION OF UNSATURATED POLYESTER RESIN-BASED PHOTOLUMINESCENT COMPOSITES

Abstract

Abstract: Polyester resin-based photoluminescent composites were prepared by using unsaturated polyester resin with different amounts of rare-earth phosphor powders. The effects of the amounts of phosphor powders on the properties of resin were studied. The results demonstrate that resin can be combined with phosphor powders well through mechanical mix and ultrasonic operations. Luminescence quenching phenomenon is not observed and the light emission effect is enhanced with increasing the amount of phosphor powders. Phosphor powders /resin CM with the best mechanical properties was obtained when the mass fraction of phosphor powders is ten percents.

Key words: rare-earth phosphor powder, unsaturated polyester resin, composite material

CLC Number:

TB332

WANG Wei, SHI Jun-hu, JING Cheng-bin. PREPARATION OF UNSATURATED POLYESTER RESIN-BASED PHOTOLUMINESCENT COMPOSITES[J]. COMPOSITES SCIENCE AND ENGINEERING, 2013, 0(5): 22-24.

References

[1] 姚光庆,张亮,苏勉曾. 高等学校化学学报[J]. 1997,18(1) : 1-5.
[2] 李建宇. 稀土发光材料及其应用[M]. 北京: 化学工业出版社, 2003. 139-151.
[3] 张希艳. 稀土发光材料[M]. 北京: 国防工业出版社,2005. 35-36.
[4] 王安东,陈阳,李嘉生. 改性环氧基复合材料工艺性能试验研究[J]. 玻璃钢/复合材料,2011,(4) : 118-120.
[5] 杜彬斌,李军,岛国和彦. TDI 增稠改性SMC 研究[J]. 玻璃钢/复合材料,2012,(2) : 44-46.
[6] 俞科静,沙晓菲,曹海建,钱坤. 表面改性二氧化硅粒子对剪切增稠液的影响[J]. 玻璃钢/复合材料,2012,(4) : 23-27.
[7] 齐双春,赵英强,吕海燕. 纳米CaC0₃ 粒子对不饱和聚酯树脂性能影响研究[J]. 玻璃钢/复合材料,2007,(4) : 31-3.
[8] 杨中文,刘西文,罗承友,彭瑛. 夜光玻璃钢安全帽外壳的研制[J]. 塑料工业,2008,36(9) : 68-51.
[9] 刘力,张秀娟,金日光,杨程,贺磊,张婉,张立群. 夜光玻璃钢安全帽外壳的研制[J]. 塑料工业,2008,36(9) : 68-51.
[10] 吉小利,徐国财,王君. 改性纳米氮化硅/EP 复合材料的力学和荧光性能研究[J]. 塑料工业,2010,(12) : 26-30.
[11] 严长浩,王庭慰,张明,陈晓松,陈海燕,邱关明. 羧酸稀土配合物共聚反应的研究[J]. 中国稀土学报,2003,(4 ) : 170-173.
[12] 陈红,侯运城,邹林,沈大理,鲍子娜,范君怡. 2006-2007 年国内外不饱和聚酯树脂工业进展[J]. 热固性树脂,2008, (3) : 44-50.
[13] 沈开猷. 不饱和聚酯树脂及其应用[M]. 北京: 化学工业出版社,2005. 1-59.
[14] 张小坪,周祝林. 不饱和聚酯树脂在复合材料中的应用[J]. 纤维复合材料,2008,(1) : 28-31.
[15] Blasse G,Grabmaier B C.Luminescent Materials[J]. Berlin-Heidelberg: Springer-Verlag,1994(5) : 12-16.
[16] GB/T2567-2008,树脂浇注体性能测试方法[S].