风电叶片用聚氨酯模内胶衣的工艺适用性研究

玻璃钢/复合材料 ›› 2017, Vol. 0 ›› Issue (6): 64-67.

风电叶片用聚氨酯模内胶衣的工艺适用性研究

牟书香^1,2,周连侠¹

1.中材科技风电叶片股份有限公司,北京102101;
2.特种纤维复合材料国家重点实验室,北京102101

收稿日期:2016-11-22 出版日期:2017-06-28 发布日期:2017-06-28
作者简介:牟书香(1981-),女,研发工程师,博士,主要从事风电叶片相关材料及工艺方面的研究,mushuxiang@126.com。
基金资助:
国家国际科技合作专项资助项目(2015DFA61270)

RESEARCH ON PROCESSING APPLICABILITY OF IN-MOULD POLYURETHANE GEL-COATINGS USED FOR WIND TURBINE BLADES

MU Shu-xiang^{1, 2}, ZHOU Lian-xia¹

1.Sinoma Wind Power Blade Co., Ltd., Beijing 102101, China;
2.State Key Laboratory of Special Fiber Composite Material, Beijing 102101, China

Received:2016-11-22 Online:2017-06-28 Published:2017-06-28

摘要/Abstract

摘要： 模内涂装是提高风电叶片涂装效率的一种有效方式。相比模外涂层体系,风电叶片用模内涂层体系在工艺性能方面有一些特殊性要求。研究了三种聚氨酯模内胶衣在风电叶片中的工艺适用性,通过可操作性、占模时间、与玻璃钢之间的附着力、在实际叶片模具上的脱模性能以及脱模后对其覆盖的玻璃钢中灌注缺陷的可观察性等性能研究发现,其中两种聚氨酯模内胶衣适用于风电叶片的生产工艺过程。

关键词: 风电叶片, 防护涂层, 模内胶衣, 聚氨酯, 涂装效率

Abstract: Using in-mold coatings is an effective way to improve the coating efficiency of wind turbine blades. There are some special requirements for the processing performance of the in-mould coating system compared with the outer-mould coating system for wind turbine blades. This paper studies the processing applicability of three kinds of in-mold polyurethane gel-coatings used in wind turbine blades. Through research on manipulability, in-mold time, pull-off strength between gel-coating and glass fiber reinforced epoxy composite, release properties in actual wind blade mold, and the observability of the defects in glass fiber reinforced composite covered by coating, it draws a conclusion that two kinds of in-mold polyurethane gel-coating are fit for the production process of wind turbine blades.

Key words: wind turbine blades, protective coating, in-mould coating, polyurethane, painting efficiency

中图分类号:

TB332

牟书香,周连侠. 风电叶片用聚氨酯模内胶衣的工艺适用性研究[J]. 玻璃钢/复合材料, 2017, 0(6): 64-67.

MU Shu-xiang, ZHOU Lian-xia. RESEARCH ON PROCESSING APPLICABILITY OF IN-MOULD POLYURETHANE GEL-COATINGS USED FOR WIND TURBINE BLADES[J]. Fiber Reinforced Plastics/Composites, 2017, 0(6): 64-67.

参考文献

[1] 吴辉. 风电叶片材料及其防护涂料的发展与应用[J].上海涂料,2015,53(8): 26-29.
[2] 郭军力. 风枫叶片涂料现状与发展趋势[J]. 中国涂料, 2015, 30(5): 15-19.
[3] 王晓, 王华进, 赵薇, 等. 风电叶片涂料用树脂研究进展[J]. 表面技术, 2016, 45(6): 28-35.
[4] 张文毓. 风电叶片防护涂料的研究进展[J]. 上海涂料, 2014(10): 38-41.
[5] 吴瑞鹏. 风力发电机叶片涂料[J]. 环球市场信息导报, 2013(8): 121-121.
[6] Storm B K. Surface protection and coatings for wind turbine rotor blades[J]. Advances in Wind Turbine Blade Design and Materials, 2013, 115(115): 387-412.
[7] Valaker E A, Armada S, Wilson S. Droplet erosion protection coatings for offshore wind turbine blades[J]. Energy Procedia, 2015, 80: 263-275.
[8] Sahoo P, Das S K, Davim J P. 3.3 surface finish coatings[J]. Reference Module in Materials Science and Materials Engineering, from Comprehensive Materials Finishing, 2017(3): 38-55.
[9] TPI Composites, Inc. Blade manufacturing improvements-Development of the ERS-100 blade[R]. Final Project Report Prepared for Sandia National Laboratories, 2001.
[10] Eisemon k E. The use of polyaspartic gel coats for the improvement of wind turbine composite blades[D]. Masters Thesis of Case Western Reserve University, 2009.
[11] Winding up technologies for better throughput, quality[Z]. http://americanmachinist. com/qc-and-inspection/winding-technologies-be-tter-throughput-quality, 2010.
[12] Det Norske Veritas. Design and manufacture of wind turbine blades, offshore and onshore wind turbines[S]. STANDARD DNV-DS-J102, 2010.
[13] Gombos Z J, Summerscales J. In-mould gel-coating for polymer composites[J]. Composites Part A: Applied Science and Manufacturing, 2016, 91(1): 203-210.[14] Rogers W, Hoppins C, Gombos Z, et al. In-mould gel-coating of polymer composites: a review[J]. Journal of Cleaner Production, 2014, 70(70) : 282-291.
[15] Stewart R. Wind turbine blade production - new products keep pace as scale increases[J]. Reinforced Plastics, 2012,56(1): 18-25.