变刚度铺放改善单钉双剪螺栓连接拉伸强度

玻璃钢/复合材料 ›› 2017, Vol. 0 ›› Issue (2): 26-31.

变刚度铺放改善单钉双剪螺栓连接拉伸强度

牛雪娟^{1, 2}, 杨涛^{1, 2}, 李阳¹

1.天津工业大学机械工程学院,天津300387;
2.天津市现代机电装备技术重点实验室,天津300387

收稿日期:2016-09-28 出版日期:2017-02-28 发布日期:2017-02-28
作者简介:牛雪娟(1977-),女,博士,副教授,主要从事复合材料的制备及工艺方面的研究。
基金资助:
国家自然科学基金(11502164)

TENSILE STRENGTH IMPROVEMENT OF SINGLE BOLT DOUBLE SHEARING BY VARIABLE STIFFNESS PLACEMENT

NIU Xue-juan^1,2, YANG Tao^1,2, LI Yang¹

1.School of Mechanical Engineering,Tianjin Polytechnic University, Tianjin 300387, China;
2.Advanced Mechatronics Equipment Technology Tianjin Area Major Laboratory, Tianjin 300387, China

Received:2016-09-28 Online:2017-02-28 Published:2017-02-28

摘要/Abstract

摘要： 沿最大主应力方向的变刚度铺放可有效提高复合材料构件的强度。以与孔周围设定区域内,单元格上流场速度矢方向与有限元得到的最大主应力方向之间的差异最小为优化目标,优化有势流场构造参数,从而得到优化的变刚度铺层轨迹。该方法得到的变刚度铺层能最大程度地使纤维主方向与层合板在该点处的最大主应力方向一致。研究结果表明,变刚度铺放不仅可提高层合板的拉伸强度,还可使试件在达到极限载荷后的承载能力下降速度平缓,从而降低了发生瞬时性损坏的概率。

关键词: 变刚度铺放, 单钉双剪螺栓连接, 有势流场, 最大主应力方向

Abstract: The variable stiffness placement along the direction of the maximum principal stress can enhance the strength of composite laminate. By focusing on the area around the hole, the optimization objective is defined as the minimization of the directional difference between the velocity vectors at the cells in the flow field and the maximum principal stress obtained by the FE. Based on this optimization objective, the optimum parameters of the flow field are calculated. Then the tape paths on the variable-stiffness ply are determined, what are consistent with the direction distribution of the maximum principal stress as far as possible. The comparative experiments of the laminates show that the average ultimate tensile strength of the variable stiffness laminates was increased. Moreover, the declining of the load bearing capability of the variable stiffness laminates is slowing when the tensile load exceeds the ultimate strength, which reduces the occurrence rate of instantaneous failure.

Key words: variable stiffness placement, single bolt double shearing joint, potential flow field, maximum principal stress direction

中图分类号:

TB332

牛雪娟, 杨涛, 李阳. 变刚度铺放改善单钉双剪螺栓连接拉伸强度[J]. 玻璃钢/复合材料, 2017, 0(2): 26-31.

NIU Xue-juan, YANG Tao, LI Yang. TENSILE STRENGTH IMPROVEMENT OF SINGLE BOLT DOUBLE SHEARING BY VARIABLE STIFFNESS PLACEMENT[J]. Fiber Reinforced Plastics/Composites, 2017, 0(2): 26-31.

参考文献

[1] 姚星宇, 王建军, 翟学. 航空发动机螺栓连接薄层单元建模方法[J]. 北京航空航天大学学报, 2015, 41(12): 2269-2279.
[2] 闵昌万, 谭志勇, 费庆国. 复合材料热结构螺栓连接刚度试验分析方法[J]. 南京航空航天大学学报, 2012, 44(6): 876-880.
[3] Sun H T, Chang F K, Qing X. The response of composite joints with bolt-clamping loads, part II: model verification[J]. Journal of Composite Materials, 2002, 36(1): 69-92.
[4] Ylmaz T, Snmazelik T. Investigation of load bearing performances of pin connected carbon/polyphenylene sulphide composites under static loading conditions[J]. Materials & design, 2007, 28(2): 520-527.
[5] Alaattin Aktas.Bearing strength of carbon epoxy laminates under static and dynamic loading[J].Composite Structures, 2005, 67 (4): 485-489.
[6] P.M.G.P.Moreira, P.F.P.de Matos, P.P Camanho. Stress intensity factor and load transfer analysis of a cracked riveted lap joint[J]. Material and Design, 2007,28: 1263-1270.
[7] 袁喆, 刘军, 闫五柱, 等. 双剪切连接件钉传载荷分析及其均化处理[J]. 材料科学与工程学报, 2013(1): 88-91.
[8] 刘哲, 金达锋, 范志瑞. 基于密度分布曲线法的复合材料变刚度铺层优化[J]. 复合材料学报, 2015, 32(06): 1737-1744.
[9] 秦永利, 祝颖丹, 蔡晶, 等. 基于VAT技术的复合材料层合板螺栓连接补强研究[J]. 玻璃钢/复合材料, 2012(S1): 68-72.
[10] 孟毛毛, 王文智. 铺层比例对层合板连接结构损伤特性影响分析[J]. 航空工程进展, 2016(3): 332-337.
[11] Jafari M, Ardalani E. Stress concentration in finite metallic plates with regular holes[J]. International Journal of Mechanical Sciences, 2016, 106: 220-230.
[12] Niu X J, Yang T, Du Y, et al. Tensile properties of variable stiffness composite laminates with circular holes based on potential flow functions[J]. Archive of Applied Mechanics, 2016, 86(8): 1-13.
[13] Gürdal Z. , Olmedo R. In-plane response of laminates with spatially varying fibre orientations: Variable stiffness concept[J]. AIAA Journal, 1993, 31(4):751-758.
[14] Hyer M W, Lee H H. The use of curvilinear fiber format to improve buckling resistance of composite plates with central circular holes[J]. Composite structures, 1991, 18(3): 239-261.
[15] M W Tosh, D W Kelly. Fiber steering for a composite C-beam[J]. Composite Structures, 2001, 53(2):133-141.